BMB-III-"Laminar-S."-1,8 PROTECT VIS-A-VIS Class III



Article 2Е-С.002-18

The cabinet is designed for operators working simultaneously opposite one another.

If connected to the individual active exhaust system, the cabinet could be used for protection from small amounts of toxic chemical substances and radionuclides.

The system of monitoring with the audio-visible indication system warns operator about the failure of working modes in the cabinet.  



Application of the Biological Safety Cabinet Class III:

  • Protection of an operator and environment from airborne infection when working with pathogenic biological agents (PBA) and microorganisms including highly (especially) hazardous pathogenic groups. 
  • Protection of the work agents inside the work chamber from external contamination.
  • If connected to the individual active exhaust system, cabinet can be used for work with toxic chemical substances and radio nuclides in low quantities and for odor removal from the work agents.
  • Cabinet is designed to equip workstations in the medical, pharmaceutical, and other institutes working with microorganisms of I-II-III-IV pathogenic groups and with parasitic disease agents 

Main Features


  • The work chamber is made of AISI 304 stainless steel;
  • Front sash can be lifted for equipment loading. Sash is resistant to UV-light and disinfectant solutions;
  • Each window has four oval-shaped glove ports; the glove ports are featured with catches for self-contained glove integrity testing module (not part of the delivery set; can be supplied as an additional option);
  • Each glove port is equipped with a butyl chamber glove and a silicon sealing O-ring. Features of the gloves: high impermeability (water, gas, vapor), used at wide temperature range, resistant to solvents and high-concentration acids, used for medical, pharmaceutical, chemical and biotechnological research;
  • Ten-liter liquid gathering tray without drain made of AISI 304 stainless steel is located in the bottom of the work chamber;
  • Two work chamber LED lighting units;
  • Removable electrical sockets in the work chamber (on the left side wall);
  • UV light inside the chamber;
  • Pressure gauge of -500 Pa to +500 Pa.

Purification System of Supplied and Exhausted Air

  • Filtering system of the air supplied to the chamber has two steps: preliminary coarse filter G4 and plenum НЕРА-filter Н14 located above the work chamber;
  • Two-step filtering system of the air exhausted from the work chamber is executed through two consecutive HEPA filters Н14;
  • Supply and exhaust filtering module for removal of the air from the chamber is supplied with two fans.

Pass Box

  • Outer panels of the pass box are made of metal covered with powder enamell;
  • Inner chamber is leak-tight and made of AISI 304 stainless steel; 
  • Angular door location: outer door is in front, inner door is built into the side wall of the work chamber;
  • The doors of the pass box are equipped with latch handle made of AISI 321 stainless steel;
  • The doors of the pass box are featured with electromechanical handle locks preventing simultaneous opening of both of the doors ;
  • Windows of the pass box are made of tempered glass.
  • LED lighting of the pass box;
  • UV light;
  • Pullout tray made of AISI 304 stainless steel ensuring easy transferring of the objects from the pass box into the work chamber.

Control System

  • Microprocessor control system of the electroautomatics;
  • Cabinet’s control unit is a touchscreen;
  • Sluice control unit is a button box with indication of sluice’s doors and locks statuses;
  • Air balance parameters sensors;
  • Built-in power cord;
  • Separate safety devices for fans and removable sockets;
  • Switch for removable sockets unit installed in the work chamber 

Control Elements of Air Flow Parameters

  • Built-in air-sampling outlets for testing the HEPA filter integrity

Class III biosafety cabinet options

  • self-contained module for testing the glove integrity



Installation work chamber air cleanliness class for suspended particle (aerosol) concentration as per ISO 14644-1

-for particles of 0.5µm and more

-for particles of 5.0µm and more



ISO 5 

ISO M (20; ≥5µm); LSAPC

Cabinet class according to ЕN 12469, NSF/ANSI 49 III
Class of the installed НЕРА-filters according to EN 1822-1 H14
Prefilter Class according to EN 779 G4
Illuminance level in the working zone, lux, not less than 2000
Minimal negative pressure in the working chamber, Pa, not less than  200
Permanently provided working negative pressure in the working chamber, Pa, not less than 250

Air inflow filtering
Air outflow filtering

two-stage (G4, H14)
two-stage (Н14, H14)
Air recirculation rate in the cabinet, % no recirculation


BMB-III-"Laminar-S."-1,8 PROTECT VIS-A-VIS Class III

Article 2Е-С.002-18

Maximum dimensions of the cabinet with pass box* (WxDxH), mm

Dimensions of the work chamber (WxDxH), mm 1640х655х685
Maximum net weight of the cabinet with stand, kg 400
Rated input power (without built-in electric sockets), W 460
Maximum allowed load on the built-in electric sockets, W 1000
Air volume supplied to the work chamber of the cabinet, m3/h 400-450

*Dimensions do not account for outstanding supports. 

DIMENSION DRAWING (Article 2Е-С.002-18)

Dimensional drawing -class III Protect Vis-A-Vis(332.120)

Order product

Attention! Fields marked with * are mandatory for filling